Del Mar Photonics  - Greyhawkoptics

Del Mar Photonics manufactures custom passive photonic components for telecom research and applications (1550 nm light).

Here are just few examples of recently manufactured OEM components:


a) True Zero - order Quartz waveplates, sizes about 1.5 x 1.5 x 0.09 mm;
b) Zero - order Quartz waveplates, sizes about 2 x 2 x 2 mm;
c) TiO2 beamdisplacers, 2 x 3 x 10 mm;
d) Calcite beamdisplacers, 6 x 8 x 30 mm;
e) TiO2 plates 1.4 x 1.6 0.225 mm;
f) LiNbO3 plates 1.4 x 1.6 x 0.75 mm;
g) PbMoO4 crystals, 2.6 x 2.6 x 2.4 mm;
 

Email for a quote

Rutile (TiO2) coupling prisms and their applications - buy online - download brochure

Del Mar Photonics offers optical elements made of high quality synthetically grown Rutile Titanium Dioxide crystals. Rutile抯 strong birefringency, wide transmission range and good mechanical properties make it suitable for fabrication of polarizing cubes, prisms and optical isolators. Boules having high optical transmission and homogeneity are grown by proprietary method. Typical boules have 10 - 15 mm in dia. and up to 25 mm length. Optical elements sizes - from 2 x 2 x 1 mm to 12.7 x 12.7 x 12.7 mm. Laser grade polish quality is available for finished elements. So far we the largest elements that we manufactured are 12 x15 x 5 mm, in which optical axis is parallel to 15 mm edge, 5 mm is along beam path, 12 x 15 mm faces polished 20/10 S/D, one wave flatness, parallelism < 3 arc.min. (better specs. available on request).
 

Standard Specifications (buy online):

Rutile (TiO2) coupling prism
Material: single crystal TiO2
Sizes: 5x5x5 mm +/- 0.2 mm
Angles:45-45-90 deg.+/-10 arcmin
Polish quality: 20/10Scratch/Dig
Surface flatness: lambda @ 633nm
Parallelism: <5arcmins
Orientation: Z-axis along prism thickness +/- 15 arcmin

Research description for a Rutile coupling prism

This description will give a brief insight into our research at the Light Technology Institute of the University of Karlsruhe (TH), Germany. One of our research fields is the development of electrically pumped organic semiconductor thin film lasers. Due to the complex behavior of these lasers numerous electrical and optical characterization is necessary. One of the most important optical properties of these organic semiconductor laser structures is the attenuation coefficient of the multilayer waveguide, which has to be carefully optimized to reduce waveguide losses 1. The first step in the optimization process is the numerical simulation of the anticipated waveguide design. Next, the optimized sample structure is fabricated and characterized in our attenuation measurement setup. This measurement is done as follows:
A Rutile coupling prism is pressed onto the waveguide. A laser beam is then coupled into the prism so that total reflection occurs inside the prism at the interface to the waveguide. In the vicinity of the waveguide the overlapping incident and reflected beam generate a standing wave. The evanescent field of that standing wave penetrates into the waveguide.





Evanescent field coupling



Under a certain angle and if the phase match conditions are fulfilled, the evanescent field stimulates a mode that is guided by the waveguide. The phase match condition can only be achieved when the refractive index of the prism is at least as high as the effective refractive index of the waveguide. Owing to its high refractive index, Rutile is an ideal material for use as a coupling prism in such a prism-coupler waveguide attenuation measurement setup.
 


Beam coupling into waveguide



A small fraction of the guided light is scattered out of the waveguide. The intensity of this scattered light is assumed to be proportional to the intensity of the guided light. Thus the intensity distribution inside the waveguide along the propagation direction can be directly determined through measuring the intensity of the scattered light.




Streak caused by scattering inside the waveguide



The intensity distribution is detected with a computer controlled, cooled CCD-Camera. Finally the attenuation coefficient is extracted from the measured data.




Intensity distribution measured with CCD-Camera




The following two figures show the setup that was used for the measurements.
 




Schematic of the Setup
 



Photography of the Setup



Additionally, it is possible with our setup to measure the refractive index and the thickness of waveguides that support a minimum of two guided modes. These parameters can be extracted from the dependency between coupling angle and effective refractive index.

Keywords: Prism, Coupling, Thin film waveguide, Waveguide losses, scattering, Effective refractive index, Organic semiconductor lasers, Polymer, Small molecule, Evanescent field, CCD-Camera, Coupling angle

1 M. Reufer, J. Feldmann, P. Rudati, A. Ruhl, D. Müller, K. Meerholz, C. Karnutsch, M. Gerken, and U. Lemmer, Appl. Phys. Lett. 86, 221102 (2005).
 

MSc.Christian Karnutsch
Lichttechnisches Institut
Universität Karlsruhe (TH)
Geb. 30.34
Kaiserstraße 12
D-76131 Karlsruhe

Raum: 126
Telefon: +49 721 608 7742
Telefax: +49 (0)721 608 - 2590


Del Mar Photonics

护士被强奷系列视频_黄色电影片_黄色视频网